Product Details

AV12

Superior Sensors for No-Bearing Encoders

  • Wide-Gap Technology eliminates gapping and shimming
  • Mount in AV125 encoders
  • Usable for "pod+disk" applications
  • All electronics fully potted and sealed
  • -40°C to +100°C standard; +120°C option requires encoder cooling
  • 3 Year No-Hassle Warranty
Avtron AV12 SMARTach™ III sensors are magnetoresistive, severe duty incremental quadrature sensors for the AV125 rotary encoder. The AV12 is also usable in applications where an encoder housing is not needed – simply mount the AV12 with your bracket, and use an AV125 or other rotor.

The AV12 + AV125 rotor allows large through-shaft applications up to 7 7/8" [200mm], ideal for large hollow shaft motors, large brakes and applications requiring large bore hollow shafts for application cooling water or cooling air.

The AV12 offers a full range of electrical connector options, including IP67 cable, IP66 MS connectors, and IP65 Industrial with built-in terminal strips. The AV12 sensor is fully protected against all types of wiring errors, including short circuits, reverse voltage, and phase-to-phase shorts. It is one tough sensor! For smaller bore applications, use AV5 sensors with the AV685 or AV850 encoder (or as stand-alone).

The universal 5-24V design drives longer cables and is protected against wiring errors and surges.

Adaptive Electronics: At power-up you know you installed it right! The green LED tells you your AV12 Sensor is aligned with the rotor and reading signal.  If at any time, the AV12 cannot produce consistent signals, the LED changes to red and the optional remote alarm contact activates. However, the encoder keeps working to give you time to schedule service.  Even wiring errors and short circuits that cause an over-temp situation will be detected and indicated by changing the LED to orange.
Operating Power: Volts: 5 - 24 VDC*
Current: 100mA nom, no load
Output Signals:  A Quad B with Marker (A,/A, B,/B, Z,/Z)
Frequency Range
     @5V, @1m cable, 250 kHz Max
     @24V, @300m cable, #8 output, 45 kHz Max
Maximum Cable Length: 1000' 
PPR:
4-50000***
Speed: 5400 RPM Max****
Temperature Range:  -40° to 120°C^
Electronics: Fully Encapsulated - IP67**
Vibration: 18G
Shock: 1 meter drop test
Chemical: Polyurethane enamel paint protects against salt spray, mild acids, and bases.
Weight: 2 - 3 lbs [0.9 - 1.36 kg] (will vary by connector options)


*  Electrical specifications for SMARTach III model (serial #30,000 or higher), consult Nidec Industrial Solutions for earlier model specifications.
** Certain connector options may affect IP rating.
***(PPR) Standard maximum PPR is 5000. Consult Factory with your application for PPRs up to 50,000.
**** (Speed) Maximum RPM may be limited for PPR > 2,500. Consult Factory with your application.
^ Requires air cooling system option in AV485 & AV685 to reach +120°C rating


All dimensions are in inches [millimeters].
Specifications and features are subject to change without notice.
  • High resolution up to 8192 PPR
  • Sensor PPR can be factory reprogrammed
  • Full protection against short circuits, reverse voltage, phase-to-phase shorts
  • High-power outputs for long cable runs
  • Optional 24V in, 5V out option for low-voltage, long-cable applications
  • Diagnostic LED and alarm output contact indicates proper operation

No Related Materials Available

Competitive Products

  • Avtron SMARTach II Encoders enable replacement of unreliable, easily damaged sensors including:

    Lakeshore/Northstar:

    NSR10240LLC

    NSR10256LLC

    NSR10512LLC

    NSR10152ZLC

    NSR10960LLC

    NSR10960ZLC

    NSR11024LLC

    NSR11024ZLC

    NSR11200LLC

    NSR11200ZLC


    SMARTach II encoders are pin-for-pin compatible replacements so no cabling changes need to be made, including factory cable assemblies including

    RIMCABLEDB1


    For direct model replacements, try our cross reference page

    or

    Contact Us

Related Products

Rating & review

See all reviews